Search by Vehicle

Rear Track Bar Bracket - Jeep JT Gladiator 4WD 2020-2024

$119.95
In stock
SKU
67-6000

Includes New Heavy-Duty Rear Track Bar Bracket for 2020-2024 Jeep Gladiator vehicles. Fits JT Gladiators with 3.0" to 4.0" Lifts Mounts directly to rear axle housing to correct track bar angle and properly center rear axle.

Have a question? Please call 800-549-4620

TIRE/WHEEL SIZING GUIDE

  • Jeep Gladiator JT Heavy Duty Rear Track Bar Bracket - USA Made! The 67-6000 Heavy-Duty Series REAR TRACK BAR BRACKET is an important component for lifted JT Gladiator vehicles after lifting. This kit includes one (1) bolt-on ReadyLIFT Heavy-Duty Series track bar bracket and hardware. This Rear Track Bar Bracket helps to correct important suspension geometry both on and off road. The bracket aids in keeping the rear track bar aligned properly with the axle housing while also providing a super strong axle mounting point for when severely articulating the Jeep suspension in an off road or rock crawling environment.
  • (1) Heavy-duty fabricated steel rear track bar bracket with all necessary hardware.

  • SAEJ2492 WARNING: By installing this product, you acknowledge that the suspension of this vehicle has been modified. As a result, this vehicle may handle differently than factory-equipped vehicles. As with any vehicle, extreme care must be used to prevent loss of control or rollover during sharp turns or abrupt maneuvers. Always wear seat belts, and drive safely, recognizing that reduced speeds and specialized driving techniques may be required. Failure to drive this vehicle safely may result in serious injury or death. Do not drive this vehicle unless you are familiar with its unique handling characteristics and are confident of your ability to maintain control under all driving conditions. Some modifications (and combinations of modifications) are not recommended and may not be permitted in your state. Consult your owner's manual, the instructions accompanying this product, and state laws before undertaking these modifications. You are responsible for the legality and safety of the vehicle you modify using these components.

     

    INSTALLATION ALIGNMENT NOTE:  Your vehicle may require alignment after product installation.  You may incur additional costs to align the vehicle.

     

    INSTALLATION HEADLAMP AIM NOTE:  In addition to your vehicle alignment, for your safety and others, it is necessary to check and adjust your vehicle headlamps for proper aim and alignment after product installation.  You may incur additional costs to adjust the headlamp system.

     

    INSTALLATION ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS) NOTE:  If your vehicle is equipped with active or passive safety/collision monitoring and/or assistance/avoidance systems including, but not limited to, camera- or radar/sonar-based systems, check and adjust your vehicle’s systems for proper aim and function after product installation.   In some instances, your vehicle may require OEM dealer service tools and factory-trained technicians to re-calibrate ADAS.  You may incur additional costs to adjust ADAS systems.

    Estimated Installation Time: 0.9 Hours +/- 0.5 hours (excluding alignment and wheel/tire assembly)

    Have a certified mechanic do it for you!


Quick Overview
Includes New Heavy-Duty Rear Track Bar Bracket for 2020-2024 Jeep Gladiator vehicles. Fits JT Gladiators with 3.0" to 4.0" Lifts Mounts directly to rear axle housing to correct track bar angle and properly center rear axle.
Details
Jeep Gladiator JT Heavy Duty Rear Track Bar Bracket - USA Made! The 67-6000 Heavy-Duty Series REAR TRACK BAR BRACKET is an important component for lifted JT Gladiator vehicles after lifting. This kit includes one (1) bolt-on ReadyLIFT Heavy-Duty Series track bar bracket and hardware. This Rear Track Bar Bracket helps to correct important suspension geometry both on and off road. The bracket aids in keeping the rear track bar aligned properly with the axle housing while also providing a super strong axle mounting point for when severely articulating the Jeep suspension in an off road or rock crawling environment.
Kit Components

(1) Heavy-duty fabricated steel rear track bar bracket with all necessary hardware.

Installation

SAEJ2492 WARNING: By installing this product, you acknowledge that the suspension of this vehicle has been modified. As a result, this vehicle may handle differently than factory-equipped vehicles. As with any vehicle, extreme care must be used to prevent loss of control or rollover during sharp turns or abrupt maneuvers. Always wear seat belts, and drive safely, recognizing that reduced speeds and specialized driving techniques may be required. Failure to drive this vehicle safely may result in serious injury or death. Do not drive this vehicle unless you are familiar with its unique handling characteristics and are confident of your ability to maintain control under all driving conditions. Some modifications (and combinations of modifications) are not recommended and may not be permitted in your state. Consult your owner's manual, the instructions accompanying this product, and state laws before undertaking these modifications. You are responsible for the legality and safety of the vehicle you modify using these components.

 

INSTALLATION ALIGNMENT NOTE:  Your vehicle may require alignment after product installation.  You may incur additional costs to align the vehicle.

 

INSTALLATION HEADLAMP AIM NOTE:  In addition to your vehicle alignment, for your safety and others, it is necessary to check and adjust your vehicle headlamps for proper aim and alignment after product installation.  You may incur additional costs to adjust the headlamp system.

 

INSTALLATION ADVANCED DRIVER ASSISTANCE SYSTEMS (ADAS) NOTE:  If your vehicle is equipped with active or passive safety/collision monitoring and/or assistance/avoidance systems including, but not limited to, camera- or radar/sonar-based systems, check and adjust your vehicle’s systems for proper aim and function after product installation.   In some instances, your vehicle may require OEM dealer service tools and factory-trained technicians to re-calibrate ADAS.  You may incur additional costs to adjust ADAS systems.



DO IT YOURSELF: Please read Instructions thoroughly and completely before beginning installation. Installation by a certified mechanic is recommended. ReadyLIFT Suspension Inc. is NOT responsible for any damage or failure resulting from improper installation. Download Pdf Instructions
Estimated Installation Time: 0.9 Hours +/- 0.5 hours (excluding alignment and wheel/tire assembly)

Have a certified mechanic do it for you!